Difference between revisions of "ONE PROCEDURE TO FLUSH the ENGINE CLOSED COOLANT SYSTEM - from RC's (aka Mainesail aka Rod Collins aka Compass Marine)"

From c34.org
Jump to: navigation, search
(Created page with "From Sailnet post https://www.sailnet.com/forums/1252482-post5.html Here are RC's steps he uses to flush the closed coolant system: If changing antifreeze, the best thing to...")
 
m
Line 1: Line 1:
From Sailnet post
+
Combining a Sailnet and Cruise's Forum post:
 
https://www.sailnet.com/forums/1252482-post5.html
 
https://www.sailnet.com/forums/1252482-post5.html
 
+
http://www.cruisersforum.com/forums/archive/index.php/t-134574.html
 
Here are RC's steps he uses to flush the closed coolant system:
 
Here are RC's steps he uses to flush the closed coolant system:
  
Line 8: Line 8:
 
To do this on a Westerbeke;
 
To do this on a Westerbeke;
  
1- Remove t-stat and replace cover housing using a spare gasket
+
1- Remove t-stat and replace cover housing using a spare gasket<br />
  
2- Remove HX (might as well clean and have pressure tested.)
 
  
3- Purge old AF out of engine with pump into 5 gal bucket.
+
2- Remove HX (might as well clean and have pressure tested.)<br />
 +
 
 +
 
 +
3- Purge old AF out of engine with pump into 5 gal bucket.<br />
 +
 
  
 
4- Use an acid resistant pump and circulate Rydlyme through engine block to clean cooling passages
 
4- Use an acid resistant pump and circulate Rydlyme through engine block to clean cooling passages
Line 19: Line 22:
 
I let this run for over an hour. Periodically opening the valve all the way to let any crud blast away.
 
I let this run for over an hour. Periodically opening the valve all the way to let any crud blast away.
  
Keep the supply hose off the bottom of the bucket some.
+
Keep the supply hose off the bottom of the bucket some.<br />
 +
 
  
 
4- Flush Rydlyme with water then fill bucket with distilled water and circulate through engine.
 
4- Flush Rydlyme with water then fill bucket with distilled water and circulate through engine.
 
Once the system is flushed with Rydlyme I flush it with clear water. It takes a lot. Probably 20+ gallons before it really runs clear.
 
Once the system is flushed with Rydlyme I flush it with clear water. It takes a lot. Probably 20+ gallons before it really runs clear.
I then run 5 gallons of distilled through it and put her back together.
+
I then run 5 gallons of distilled through it and put her back together.<br />
 +
 
  
 
5- Drain off what you can of the distilled, replace HX, t-stat and add antifreeze. The "Globals" are good. Death-Cool (AKA Dex-Cool) does NOT like all the dissimilar metals in marine engines and can create Dex-Sludge.
 
5- Drain off what you can of the distilled, replace HX, t-stat and add antifreeze. The "Globals" are good. Death-Cool (AKA Dex-Cool) does NOT like all the dissimilar metals in marine engines and can create Dex-Sludge.
  
Once back together straight AF is added until the mix in the engine meets desired AF performance results. I leave the stat out until everything is bled and the AF mix is correct.
+
Once back together straight AF is added until the mix in the engine meets desired AF performance results. I leave the stat out until everything is bled and the AF mix is correct.<br />
 +
 
  
 
Death-Cool Sludge:
 
Death-Cool Sludge:
http://www.pbase.com/mainecruising/image/108349271.jpg
+
http://www.pbase.com/mainecruising/image/108349271.jpg<br />
 +
 
 +
 
 +
6- Purge air and test AF concentration with AF tester.<br />
  
6- Purge air and test AF concentration with AF tester.
 
  
 
Circulating Rydlyme:
 
Circulating Rydlyme:
http://www.pbase.com/mainecruising/image/122459307.jpg
+
http://www.pbase.com/mainecruising/image/122459307.jpg<br />
 +
 
  
 
Connection points:
 
Connection points:
http://www.pbase.com/mainecruising/image/122459310.jpg
+
http://www.pbase.com/mainecruising/image/122459310.jpg<br />
  
  
 +
<br />
 
For air purging I replace the cheap "petcock" on top of the t-stat housing with a 1/4 turn ball valve. I then add a barb and some clear hose to it. Run the hose well higher than the highest point in the cooling system. Fill the hose with AF using a transmission funnel, open valve and start engine. As the t-stat opens and closes AF will gravity feed into engine and no air will be left in the system. Air=bad.  
 
For air purging I replace the cheap "petcock" on top of the t-stat housing with a 1/4 turn ball valve. I then add a barb and some clear hose to it. Run the hose well higher than the highest point in the cooling system. Fill the hose with AF using a transmission funnel, open valve and start engine. As the t-stat opens and closes AF will gravity feed into engine and no air will be left in the system. Air=bad.  
Once the system is no longer taking AF out of the clear tube close the valve and drain the hose back into the AF container.
+
Once the system is no longer taking AF out of the clear tube close the valve and drain the hose back into the AF container.<br />
 +
 
  
 
Air Purging Valve:
 
Air Purging Valve:
http://www.pbase.com/mainecruising/image/112297123.jpg
+
http://www.pbase.com/mainecruising/image/112297123.jpg<br />

Revision as of 04:40, 19 January 2020

Combining a Sailnet and Cruise's Forum post: https://www.sailnet.com/forums/1252482-post5.html http://www.cruisersforum.com/forums/archive/index.php/t-134574.html Here are RC's steps he uses to flush the closed coolant system:

If changing antifreeze, the best thing to do, especially if your engine had or has "Death-Cool" in it, is to thoroughly flush it out, clean it, and start fresh.

To do this on a Westerbeke;

1- Remove t-stat and replace cover housing using a spare gasket


2- Remove HX (might as well clean and have pressure tested.)


3- Purge old AF out of engine with pump into 5 gal bucket.


4- Use an acid resistant pump and circulate Rydlyme through engine block to clean cooling passages The valve on the clear return hose in the bucket is to throttle the return in order to keep system pressure just below the radiator cap [exhaust manifold pressure cap -kk] blow point and to ensure all internals are cleaned with Rydlyme...

I let this run for over an hour. Periodically opening the valve all the way to let any crud blast away.

Keep the supply hose off the bottom of the bucket some.


4- Flush Rydlyme with water then fill bucket with distilled water and circulate through engine. Once the system is flushed with Rydlyme I flush it with clear water. It takes a lot. Probably 20+ gallons before it really runs clear. I then run 5 gallons of distilled through it and put her back together.


5- Drain off what you can of the distilled, replace HX, t-stat and add antifreeze. The "Globals" are good. Death-Cool (AKA Dex-Cool) does NOT like all the dissimilar metals in marine engines and can create Dex-Sludge.

Once back together straight AF is added until the mix in the engine meets desired AF performance results. I leave the stat out until everything is bled and the AF mix is correct.


Death-Cool Sludge: http://www.pbase.com/mainecruising/image/108349271.jpg


6- Purge air and test AF concentration with AF tester.


Circulating Rydlyme: http://www.pbase.com/mainecruising/image/122459307.jpg


Connection points: http://www.pbase.com/mainecruising/image/122459310.jpg



For air purging I replace the cheap "petcock" on top of the t-stat housing with a 1/4 turn ball valve. I then add a barb and some clear hose to it. Run the hose well higher than the highest point in the cooling system. Fill the hose with AF using a transmission funnel, open valve and start engine. As the t-stat opens and closes AF will gravity feed into engine and no air will be left in the system. Air=bad. Once the system is no longer taking AF out of the clear tube close the valve and drain the hose back into the AF container.


Air Purging Valve: http://www.pbase.com/mainecruising/image/112297123.jpg