Difference between revisions of "Dripless Packing"

From c34.org
Jump to navigation Jump to search
 
Line 1: Line 1:
== GFO Fiber Packing ==
+
<div style="padding: 10px; background: aqua; border: 1px solid #FFAA99; font-family: Ariel, sans-serif">
 +
<big>''' I was reading in Mainsheet that this dripless packing works well.  I have a fairly steady drip I would like to eliminate.  Does this stuff really work, is there any downside? And, is there any issue replacing the packing while the boat is in the water?  I have been told it is do-able and the amount of water which enters the boat is not to panic over.
  
<font color="red"> I was reading in Mainsheet that this dripless packing works well.  I have a fairly steady drip I would like to eliminate.  Does this stuff really work, is there any downside?
+
''Tom Lanzilli'' '''</big>
 +
</div>
  
''' ''Tom Lanzilli'' ''' </font>
 
  
 +
=== Advice from the Message Board: ===
  
== Replies: ==
+
I've had the GFO about 3 years, great stuffStill need to tighten the shaft nut occasionally.  Changing in the water is not that bad.  I took an old tee shirt, after removing the shaft nut, wrapped the shirt around the shaft a couple times securing with an overhand knot.  Kept the incoming water down to a small trickle.  Chose a shirt over a town because it compressed enough to still allow access to the nut.  Lots of ideas to remove the old packing. I used a combination of things.  Started with a "drywall" screw.  Used a 12v drill to screw it into the packingGot the first 2 layers out this wayThe last layer was too thin, used an ice pick and hemostat to scrape/pull it outDon't forget to cut the packing at a 45 rather than 90, bit more work, but it seals better.  '''Ken Juul'''  
 
 
Believe what you read in the Mainsheet!!
 
I've used the Gore packing for the past 10+ years and think it's great.  Try it, you'll like it!!! :thumb:
 
 
 
'''Ron Hill'''
 
 
 
----
 
I still have a good bunch of the $50 green goopIt still works perfectlyWhen that runs out (in another 10 years), I'll switch to the Gore from e-marine.   
 
 
 
Sounds like you've done your "homework." Bless you, sir.
 
 
 
'''Stu Jackson'''
 
  
 
----
 
----
Any issue replacing the packing while the boat is in the water? I have been told it is do-able and the amount of water which enters the boat is not to panic over.
+
To answer your question: [http://www.c34.org/wiki/index.php?title=Stuffing_box_packing Re-packing the stuffing box]There is NO problem doing it in the water, assuming your bilge pump works.  I wrote that article before Gore became available.  The content remains valid, just add GFO to the list of materials.  '''Stu Jackson'''  
 
 
'''Tom Lanzilli'''
 
 
 
----
 
I've had the GFO about 3 years, great stuffStill need to tighten the shaft nut occasionally.  Changing in the water is not that bad.  I took an old tee shirt, after removing the shaft nut, wrapped the shirt around the shaft a couple times securing with an overhand knot.  Kept the incoming water down to a small trickle.  Chose a shirt over a town because it compressed enough to still allow access to the nut.  Lots of ideas to remove the old packing.  I used a combination of things.  Started with a "drywall" screw.  Used a 12v drill to screw it into the packing.  Got the first 2 layers out this way.  The last layer was too thin, used an ice pick and hemostat to scrape/pull it outDon't forget to cut the packing at a 45 rather than 90, bit more work, but it seals better.
 
 
 
'''Ken Juul'''  
 
  
 
----
 
----
To answer your question: http://www.c34.org/wiki/index.php?title=Stuffing_box_packingThere is NO problem doing it in the water, assuming your bilge pump works.
+
Believe what you read in the Mainsheet!!  I've used the Gore packing for the past 10+ years and think it's great.  Try it, you'll like it!!!  Look in the Mainsheet Tech notes and I published an article on "Replacing your packing while still in the Water."  Follow the article's instructions and there is little water that will come in. I re-did mine (in the water) last spring and it works fine. Needed to check to see how my old packing was doingIt was doing fine and that was about 10years of 200 hours/year!!  I believe in projects there's a picture of my feet and my packing gland while I changed to the Gore packing. Did that back many years ago. Also I made my own old packing removal tool out of a coat hanger.  Bend the end 1/2" long degrees and sharpen it.  The packing tool is from an earlier article (1992?) and it's made out of a blunt end, shaved on the sides, #2 lead pencil.  Both easy to make and both work. No big deal!  '''Ron Hill'''  
 
 
I wrote that article before Gore became available.  The content remains valid, just add GFO to the list of materials.
 
 
 
'''Stu Jackson'''  
 
  
 
----
 
----
Look in the Mainsheet Tech notes and I published an article on "Replacing your packing while still in the Water".
+
Another point on removing the old packing - I used a little stainless pointed "pick" I had in the tool box (again Home Depot) that has a 90 degree bend at the end.  I used this to clean the threads (just following the thread pitch) after I got out he old packing.  Real easy and cleaned all the threads. Seems to me that if the threads are still filled old packing, the new stuff is not going to fill the voids properly and thus - LEAKS!  '''Jim Price'''
Follow the articles instructions and there is little water that will come in.  I redid mine (in the water) last spring and it works fine.  Needed to check to see how my old packing was doing.  It was doing fine and that was about 10years of 200 hours/year!!
 
 
 
I believe in projects there's a picture of my feet and my packing gland while I changed to the Gore packing. Did that back many years ago.
 
 
 
'''Ron Hill'''
 
 
 
----
 
Everyone has been a great help.  For some reason I did find Ron's picture of how he somehow bagged the shaft.  I can not figure out where the related article is?
 
 
 
'''Tom Lanzilli'''
 
 
 
----
 
Another point on removing the old packing - I used a little stainless pointed "pick" I had in the tool box (again Home Depot) that has a 90 degree bend at the end.   
 
 
 
I used this to clean the threads (just following the thread pitch) after I got out he old packing.  Real easy and cleaned all the threads.
 
 
 
Seems to me that if the threads are still filled old packing, the new stuff is not going to fill the voids properly and thus - LEAKS!.  
 
 
 
'''Jim Price'''
 
 
 
----
 
Look in the Mainsheet tech notes, as the article is there about 1998 - written by Corky Dalton. 
 
Also I made my own old packing removal tool out of a coat hanger.  Bend the end 1/2" long degrees and sharpen it.  The packing tool is from an earlier article (1992?) and it's made out of a blunt end, shaved on the sides, #2 lead pencil.  Both easy to make and both work.  No big deal!
 
 
 
'''Ron Hill'''
 

Latest revision as of 23:58, 24 January 2009

I was reading in Mainsheet that this dripless packing works well. I have a fairly steady drip I would like to eliminate. Does this stuff really work, is there any downside? And, is there any issue replacing the packing while the boat is in the water? I have been told it is do-able and the amount of water which enters the boat is not to panic over.

Tom Lanzilli


Advice from the Message Board:

I've had the GFO about 3 years, great stuff. Still need to tighten the shaft nut occasionally. Changing in the water is not that bad. I took an old tee shirt, after removing the shaft nut, wrapped the shirt around the shaft a couple times securing with an overhand knot. Kept the incoming water down to a small trickle. Chose a shirt over a town because it compressed enough to still allow access to the nut. Lots of ideas to remove the old packing. I used a combination of things. Started with a "drywall" screw. Used a 12v drill to screw it into the packing. Got the first 2 layers out this way. The last layer was too thin, used an ice pick and hemostat to scrape/pull it out. Don't forget to cut the packing at a 45 rather than 90, bit more work, but it seals better. Ken Juul


To answer your question: Re-packing the stuffing box. There is NO problem doing it in the water, assuming your bilge pump works. I wrote that article before Gore became available. The content remains valid, just add GFO to the list of materials. Stu Jackson


Believe what you read in the Mainsheet!! I've used the Gore packing for the past 10+ years and think it's great. Try it, you'll like it!!! Look in the Mainsheet Tech notes and I published an article on "Replacing your packing while still in the Water." Follow the article's instructions and there is little water that will come in. I re-did mine (in the water) last spring and it works fine. Needed to check to see how my old packing was doing. It was doing fine and that was about 10years of 200 hours/year!! I believe in projects there's a picture of my feet and my packing gland while I changed to the Gore packing. Did that back many years ago. Also I made my own old packing removal tool out of a coat hanger. Bend the end 1/2" long degrees and sharpen it. The packing tool is from an earlier article (1992?) and it's made out of a blunt end, shaved on the sides, #2 lead pencil. Both easy to make and both work. No big deal! Ron Hill


Another point on removing the old packing - I used a little stainless pointed "pick" I had in the tool box (again Home Depot) that has a 90 degree bend at the end. I used this to clean the threads (just following the thread pitch) after I got out he old packing. Real easy and cleaned all the threads. Seems to me that if the threads are still filled old packing, the new stuff is not going to fill the voids properly and thus - LEAKS! Jim Price