Difference between revisions of "Rudder"
Kloebereng (talk | contribs) |
|||
| (10 intermediate revisions by 4 users not shown) | |||
| Line 11: | Line 11: | ||
*[[Packing Gland]]<br> | *[[Packing Gland]]<br> | ||
*[[Rust Streaks]]<br> | *[[Rust Streaks]]<br> | ||
| + | *[[Media:CTY_worn_rudder_tube_repair.pdf|Factory Repair Methods for Worn Rudder Tube - PDF file]]<br> | ||
| + | |||
| + | Note that I used the resin method, using epoxy resin mixed with graphite (see West Systems website for info on making self-lubricating bearing surfaces.) But instead of pouring resin down the tube, I used the West caulking gun tubes, injecting the mix thru several holes drilled into the backside of the rudder tube. | ||
| + | - KWKloeber 4/2015 | ||
==Steering== | ==Steering== | ||
*[[Below-deck Autopilot Considerations]] | *[[Below-deck Autopilot Considerations]] | ||
| − | *[[Media:EdsonMaintennanceGuide.pdf|Edson Cable & Wire Steering | + | |
| + | [December 2018] The following links no longer work because Edson modified their own website negating the links. If you need Edson information, visit www.edsonmarine.com | ||
| + | |||
| + | *[[Media:EdsonMaintennanceGuide.pdf|Edson Planning, Installation and Maintenance Guide (Cable & Wire Steering) PDF file]]<br> | ||
*[[Media:SteeringInspection.pdf|Edson Marine Steeering Inspection PDF file]]<br> | *[[Media:SteeringInspection.pdf|Edson Marine Steeering Inspection PDF file]]<br> | ||
*[[Media:EngineControl.pdf|Edson Pedestal Engine Control Installation PDF file]]<br> | *[[Media:EngineControl.pdf|Edson Pedestal Engine Control Installation PDF file]]<br> | ||
| Line 24: | Line 31: | ||
==Also of Interest== | ==Also of Interest== | ||
There are several articles of interest concerning Rudders in the [http://c34.org/tech-notes-index/index.htm Tech Notes] | There are several articles of interest concerning Rudders in the [http://c34.org/tech-notes-index/index.htm Tech Notes] | ||
| + | |||
| + | *[[Richie Compass Compensation]] | ||
Latest revision as of 23:31, 14 August 2020
General
With the introduction of the Catalina 34 Mark II the rudder was updated to be longer with an elliptical design. Some Mark I owners have updated their original rudders with a new Elliptical Rudder for more control and smoother handling.
Ron Hill has done his own impressive modification to the rudder on his Mark I with a Wing Keel.
- The rudder post goes through a packing gland
- Rudder Bearing drawing
- Rudder Removal drawing
Maintenance
Note that I used the resin method, using epoxy resin mixed with graphite (see West Systems website for info on making self-lubricating bearing surfaces.) But instead of pouring resin down the tube, I used the West caulking gun tubes, injecting the mix thru several holes drilled into the backside of the rudder tube. - KWKloeber 4/2015
Steering
[December 2018] The following links no longer work because Edson modified their own website negating the links. If you need Edson information, visit www.edsonmarine.com
- Edson Planning, Installation and Maintenance Guide (Cable & Wire Steering) PDF file
- Edson Marine Steeering Inspection PDF file
- Edson Pedestal Engine Control Installation PDF file
- Edson Steering Cable components PDF file
- Edson Steering Cable components PDF file
- Edson Pedestal Shaft Wheel Attachment
- Edson Marine Tech Support -Clicking this link takes you to the Edson site
Also of Interest
There are several articles of interest concerning Rudders in the Tech Notes
