fuel cut off cable

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Bobg

went to shut my engine off by pulling up on the fuel shut off handle, it went halfway and with a little more effort was able to pull it up all the way and shut the engine down, upon investigation I noticed the end of the cable sheething was pulled out of the bracket adjacent to the shutoff lever, does anyone know how this is supposed to be attached? or do I need a new cable? I thought I had pictures of my engine but can't find any to see what it used to look like attached.  Thanks
Bob Gatz, 1988 catalina 34, Hull#818, "Ghostrider" sail lake superior Apostle Islands

KWKloeber

Bob

Because the stop lever is spring-loaded the  stop cable is a "pull" so the end isn't secured (unlike the speed control cable.)  The sheath just sits against the bracket. See pic

(Of course  if yours is different just consider i am pontificating about something that I have no clue because I don't have a 34.)
Twenty years from now you'll be more disappointed by the things you didn't do, than by the ones you did.
So throw off the bowlines.  Sail away from the safe harbor.  Catch the tradewinds in your sails.
Explore.  Dream.  Discover.   -Mark Twain

Bobg

thanks Ken, when I pull up on the handle there is a catch halfway up, with a little effort I can pull it all the way up and the engine will stop, I was wondering if something was missing where the cable contacts the bracket  before the spring loaded lever, because at the end of the sheath, about a 1/4", the paint is worn off, could be the cable is getting worn somewhere else.  Diagnosing boat problems a 160 miles away is tough thank you for the picture
Bob Gatz, 1988 catalina 34, Hull#818, "Ghostrider" sail lake superior Apostle Islands

KWKloeber

My pic shows a metal thimble over the end of the sheath. Is yours missing?

Good bet it's the stop lever — check to make sure it operates and returns freely.
I have a problem with mine - it acts like the cable is stuck - but it's actually a very tight lever.

If the end of the cable isn't frayed you can detach it, pull it back, check it, lube it, etc. of course if there's any fraying you run the risk of getting the end caught when reinserting.

If your stop lever operates freely, the control cable is one of the FEW THINGS that I say don't bother troubleshooting - it's cheap insurance to replace it.
Twenty years from now you'll be more disappointed by the things you didn't do, than by the ones you did.
So throw off the bowlines.  Sail away from the safe harbor.  Catch the tradewinds in your sails.
Explore.  Dream.  Discover.   -Mark Twain

Ron Hill

Bob : Also make sure that the outside of the cable is secured and the inside cable wire didn't get bent!!

A thought
Ron, Apache #788

Bobg

yes Ken, there is no metal thimble, but it certainly looks like something should be there, I can't blow your picture up to see that, I will look next time at boat, had company leaving and couldn't really look under engine to see if a "thimble" is laying under before we had to go, and Ron I'll have to see where cable is secured to see if its loose, thanks guys
Bob Gatz, 1988 catalina 34, Hull#818, "Ghostrider" sail lake superior Apostle Islands

KWKloeber

Bob

I blewed it up.

I can't physically check but it looks to me that there's something (or was before I touched up paint?) crimped on the end.  No ragged sheath visible, but.... **
though it really shouldn't matter so long as the sheath hits the bracket and the cable is free.

Ken


**Same caveat, it's not a 34, so some hereon may say "mind your own business, we KNOW our own boats."
Twenty years from now you'll be more disappointed by the things you didn't do, than by the ones you did.
So throw off the bowlines.  Sail away from the safe harbor.  Catch the tradewinds in your sails.
Explore.  Dream.  Discover.   -Mark Twain