Does anyone offhand know how high the tall rig projects off the water?
My mast (tall rig 1990) is 51.5 feet long(tall). Given that mast base is below water line about 1.5 foot (rough assumption), air draft roughy 50', hope that helps..
Greg : I always used 50ft for may standard rig. I'd use 52' for the tall rig.
My thought
Thanks for the answers. Our stick is 45' 2" long and I have always been guessing about the height of mast step to water. We are looking at a 55 or 56 foot bridge in Charleston SC in a few days and wanted some reassurance that I was not too far off base. The Dismal Swamp took my Windex a couple of weeks ago and I am still feeling sensitive.
Quote from: dfloeter on October 27, 2019, 01:42:43 PM
>>>>>>>>>>>>>>>>>
Our stick is 45' 2" long and I have always been guessing about the height of mast step to water.
We are looking at a 55 or 56 foot bridge in Charleston SC in a few days and wanted some reassurance that I was not too far off base. The Dismal Swamp took my Windex a couple of weeks ago and I am still feeling sensitive.
I have a standard rig and have always used 55 feet. To me, Dietrich, the height of the mast step from the water is useless info, 'cuz it's
under the water line.
What I used was the IJPE info in the manual and determined the height of the deck at the mast from the water.
Then I added a foot or two for the antenna.
If you're THAT close as you said for the bridges, I suggest you do what I did and decide just how much "wiggle room" you personally feel comfortable with.
I must admit I had no fixed bridges in The Bay Area (they were either draw or swing bridges), but I always wanted to "know."
That how I did it for my own piece of mind.
Here in southwestern B.C. all I have to deal with are "low hanging" power wires. Then I get to convert feet to meters!!! :D:D:D
Good luck.
You could tie a line to a halyard and run it up to the top of the mast. Mark the length
at the deck level and then measure the line. There's your mast height above deck. Lay a long
boat hook across the deck and measure boat hook to water. Add those dimensions plus anything
on the top of the mast (light antenna etc.) Allow a little for clearance and you should be good to go.
Almost forgot, pray or wait for low tide.
Good luck.
Phil—👍
You could try this. Please take video if you do, I'd like to see a Catalina 34 do this
https://www.youtube.com/watch?v=kiv0fxFcV3I
Jim
Jim : They do that in Florida all the time going form the east to the west coast!! LOW fixed RR bridge.
A thought
Ok, I know the length of the extrusion, 45'2", and I can tie the whisker pole off athwart ship and measure both ends to the water and average the figures. Adding two feet for the masthead gear should make me more comfortable. It will be interesting just how close to the original ballpark figure of 52' it really is. Meanwhile we have the slip reserved in two days so there is no time to waste.
You can also tie some weight (water jugs?) to the whisker pole and tip/incline the boat that way if you need a little extra insurance? 8) a pole lift/topping lift on the whisker pole would also be advisable to counteract the strain on the pole. We used to use that incline/tipping method when measuring incline on IOR class rated race boats back in the day.
Ron, I've heard that "Billy the boat tipper" has retired and no one has taken his place.
Quote from: Ron Hill on October 28, 2019, 03:09:56 PM
Jim : They do that in Florida all the time going form the east to the west coast!! LOW fixed RR bridge.
A thought
Sitting in a low country creek, I measured and found there is no need to hang a water filled dinghy off the boom end. Literally measured with the entire antenna figured in, the result is where I started at 52' from the water. End of tale.