Hi all,
I have been searching for well over an hour now, including what seems like every forum entry, the 101's, "Replacement Filters, Belts, and Lubricants", FAQs, including "ENGINE FILTER / FANBELT / AIR INTAKE EQUIVALENTS" with zero luck.
Anybody have some dimensions for the engine and transmission Crush Washers? Inside and outside diameters, thickness? What I read says they should be aluminum; is copper okay? Any help would be greatly appreciated.
My crankcase drain plug is leaking, and I really should do the transmission oil. Just trying to save multiple trips to the boat.
Thanks in advance.
Steve
PS: Not been active on the board in forever, sorry, been busy with fun car stuff and my Catalina has been great not requiring anything significant for some time.
Steve : I'd suggest that you go on-line to someone that rebuilds Hurth transmissions and obtain a few of the crush washers that fit the bottom drain plug.
a thought
Quote from: Steve Wormsbecher on May 02, 2016, 09:21:39 AM
Hi all,
I have been searching for well over an hour now, including what seems like every forum entry, the 101's, "Replacement Filters, Belts, and Lubricants", FAQs, including "ENGINE FILTER / FANBELT / AIR INTAKE EQUIVALENTS" with zero luck.
Anybody have some dimensions for the engine and transmission Crush Washers? Inside and outside diameters, thickness? What I read says they should be aluminum; is copper okay? Any help would be greatly appreciated.
My crankcase drain plug is leaking, and I really should do the transmission oil. Just trying to save multiple trips to the boat.
Thanks in advance.
Steve
PS: Not been active on the board in forever, sorry, been busy with fun car stuff and my Catalina has been great not requiring anything significant for some time.
Hi Steve,
Just did that job. Here is the firm that stocks them:
Transmission Marine, Inc.
223 SW 33rd Court
Ft. Lauderdale, FL 323335
(954) 467-1540
Their part number is: 0634801281 Sealing Ring
Hope this helps,
Bob
Quote from: Steve Wormsbecher on May 02, 2016, 09:21:39 AM
Hi all,
I have been searching for well over an hour now, including what seems like every forum entry, the 101's, "Replacement Filters, Belts, and Lubricants", FAQs, including "ENGINE FILTER / FANBELT / AIR INTAKE EQUIVALENTS" with zero luck.
Anybody have some dimensions for the engine and transmission Crush Washers? Inside and outside diameters, thickness? What I read says they should be aluminum; is copper okay? Any help would be greatly appreciated.
My crankcase drain plug is leaking, and I really should do the transmission oil. Just trying to save multiple trips to the boat.
Thanks in advance.
Steve
PS: Not been active on the board in forever, sorry, been busy with fun car stuff and my Catalina has been great not requiring anything significant for some time.
Steve,
I have Hurth parts manuals. I can't post on the TW -- been looking for procedures where/how to upload PDF manuals.
So ping me if you want them.
Ken
Thanks guys,
Surprised no one's got one lying around to measure. Guess I'll have to order them rather than just getting 'em at my local car parts place.
Ken, not sure which manuals you have, but if it's not too much trouble I'd certainly appreciate them.
If email would work, please send them to stevew10@hotmail.ca
Thanks,
Steve
Try Amazon - 16mm Aluminum Crush Washer SW-10 pack of 5 by Gold Plug
Good Winds
DaveM
Quote from: Steve Wormsbecher on May 07, 2016, 11:27:31 AM
Ken, not sure which manuals you have, but if it's not too much trouble I'd certainly appreciate them.
If email would work, please send them to stevew10@hotmail.ca
Thanks,
Steve
Steve,
Done. I sent 2, I thought I had another -- still looking for it.
Ken
Ken, thanks much for those, interesting stuff.
Dave, thank you too. I'll likely zoom by my local guys and pick some up. I think the 16mm is the critical number. I'm assuming you've used those and they fit well.
Thanks again guys.
Steve
Welcome Steve.
I just uploaded a searchable PDF of the Hurth manual to the TW manuals page.
kk
I actually order 14mm to begin with and had to file them out, but worked fine. Don't ask :? From that detail work found that 16mm was the correct size.
Thanks Dave, I'll grab a few of those before heading down.
Really appreciate the insight, thanks again.
Steve
http://www.ericsonyachts.org/infoexchange/entry.php?213-Hurth-17-mm-Drain-Plug-washer
Thanks to Loren Beach.
I put it in the wiki, too.
This washer with a rubber seal bonded to the ID is at McMaster-Carr good for up to 225F
Bolt ID OD Thk min/max qty p/n $
M16 15.7 27.1 1.1 1.4 5 93786A250 11.98
If this don't work possibly one of the SAE sizes would.
5/8" 0.683" 1.187" .089"-0.099" 5 93781A035 14.32
I plan to order a package when I get to needing new washers. Unless someone out there has a "no no" about this idea.