Recent posts
#1
Main Message Board / Re: Teak trim
Last post by Noah - Today at 05:57:42 PMLots of places to buy online, but it is not cheap. Google is your friend, search "Teak lumber". I would probably start with a 3/8 in. teak board. Then (I would think) you could do all the cutting and shaping with a sabre saw/skill saw, a power sander and/or hand sanding.
#2
Main Message Board / Re: Teak trim
Last post by Roland Gendreau - Today at 05:47:52 PMPaulus,
Where did you buy the teak for the trim pieces? Could you get the same thickness?
how did you fashion the convex exdges, if not with a router?
I need to replace both of my trim pieces due to cracks.
Roland
Where did you buy the teak for the trim pieces? Could you get the same thickness?
how did you fashion the convex exdges, if not with a router?
I need to replace both of my trim pieces due to cracks.
Roland
#3
Main Message Board / Re: Adjust the cable tension f...
Last post by waughoo - Today at 12:11:59 PMLogo Freak just did this during his new fuel tank job. He used spray foam to fill it, shaved it flat and ran a few layers of glass over it. I REALLY wish I had when I rebuilt my water tank shelf. It is a challenging spot to get to for cleaning.
#4
Main Message Board / Re: Adjust the cable tension f...
Last post by pbyrne - Today at 11:20:45 AMQuote from: scgunner on Today at 07:22:25 AMRon,
Noah is correct if you've got a leak in the aft tank that should be easy to determine. Without using it if you have to keep topping it off every few weeks or couple of months the tank is obviously leaking. If that's the case you also have another problem, the leaking tank will fill the pan that it sits in and when the boat heels the water runs to that side comes forward and leaks through the bottom of the bulkhead into the aft cabin. It's also possible if you haven't changed the cockpit drain hoses that could be the culprit, when I changed mine I don't know if they were leaking but they were badly cracked.
On the "Scag Dimple" (I actually had two) there was some really nasty standing water in mine. Using epoxy and filler I faired mine in so the bottom is smooth and any water now simply runs down to the bilge.
Filling the 'dimples' in was something I was considering as well. They don't serve any purpose other than to provide a breeding ground for things I don't want on the boat!
#5
Main Message Board / Re: Adjust the cable tension f...
Last post by scgunner - Today at 07:22:25 AMRon,
Noah is correct if you've got a leak in the aft tank that should be easy to determine. Without using it if you have to keep topping it off every few weeks or couple of months the tank is obviously leaking. If that's the case you also have another problem, the leaking tank will fill the pan that it sits in and when the boat heels the water runs to that side comes forward and leaks through the bottom of the bulkhead into the aft cabin. It's also possible if you haven't changed the cockpit drain hoses that could be the culprit, when I changed mine I don't know if they were leaking but they were badly cracked.
On the "Scag Dimple" (I actually had two) there was some really nasty standing water in mine. Using epoxy and filler I faired mine in so the bottom is smooth and any water now simply runs down to the bilge.
Noah is correct if you've got a leak in the aft tank that should be easy to determine. Without using it if you have to keep topping it off every few weeks or couple of months the tank is obviously leaking. If that's the case you also have another problem, the leaking tank will fill the pan that it sits in and when the boat heels the water runs to that side comes forward and leaks through the bottom of the bulkhead into the aft cabin. It's also possible if you haven't changed the cockpit drain hoses that could be the culprit, when I changed mine I don't know if they were leaking but they were badly cracked.
On the "Scag Dimple" (I actually had two) there was some really nasty standing water in mine. Using epoxy and filler I faired mine in so the bottom is smooth and any water now simply runs down to the bilge.
#6
Main Message Board / Re: New fuel tank
Last post by waughoo - Yesterday at 11:16:11 PMExcellent milestone Antoni!! I'm excited to hear of the first fill up.
#7
Main Message Board / Re: New fuel tank
Last post by Patches - Yesterday at 09:28:42 PMHey Antoni:
We will also be sailing around Vancouver Island this summer. Leaving August 24 from Bainbridge Island and will be going counter-clockwise.
When I made the trip in 2016, the first fuel after rounding Cape Scott turned out to be at Esperanza on the NE corner of Nootka Island. We were very happy to learn they had fuel there after we topped up in Port Hardy. Nothing was available in Winter Harbor or Kyuquot in mid September. Doubling the factory fuel capacity goes a long way on that coast—and in Mexico too. Great upgrade.
Patches
We will also be sailing around Vancouver Island this summer. Leaving August 24 from Bainbridge Island and will be going counter-clockwise.
When I made the trip in 2016, the first fuel after rounding Cape Scott turned out to be at Esperanza on the NE corner of Nootka Island. We were very happy to learn they had fuel there after we topped up in Port Hardy. Nothing was available in Winter Harbor or Kyuquot in mid September. Doubling the factory fuel capacity goes a long way on that coast—and in Mexico too. Great upgrade.
Patches
#8
Main Message Board / Re: New fuel tank
Last post by LogoFreak - Yesterday at 09:01:44 PMWow, a year since I last posted 
To say things move slowly is an understatement! Finally got a good test fit done today. Should have it buttoned up within the next couple of weeks, just in time for season start!
To say things move slowly is an understatement! Finally got a good test fit done today. Should have it buttoned up within the next couple of weeks, just in time for season start!
#9
Main Message Board / Re: Adjust the cable tension f...
Last post by Noah - Yesterday at 05:50:52 PMRon—really? From the freshwater tank? Not rain, through any number of hatches, vents, etc? I would think it would be "easy" to eliminate the aft tank as the culprit?
#10
Main Message Board / Re: Adjust the cable tension f...
Last post by Ron Hill - Yesterday at 03:03:51 PMJim : We're off the topic, but I've tried to find the source of that water in the "Scag Dimple" for 30 years?? Being fresh water I'm convinced that it's from the aft water tank, but I'm NOT going thru all of the work to pull that aft tank just to find out.
A few thoughts
A few thoughts