Replacement bulb

[Paulus]

I want to replace my fluorescent tubes with the following:  12" F8T5 LED Tube for Fluorescent Fixtures (FL-T5-66)
These are from Marinebeam.  Has anyone done this change and what brightness did you choose?
The original came from West Marine and are working fine,  need more light.
Thanks, Paul

[Ekutney]

I replaced the OEM light fixture in the head with the following:

https://www.superbrightleds.com/moreinfo/led-dome-light-fixtures-non-waterproof/105-oval-dome-light-led-fixture-with-switch/1490/3465/

It provides plenty of light and fits where the previous fluorescent fixture went, a pic is below.

[Ekutney]

Just in case, another light which I found very useful was the following:

https://www.superbrightleds.com/moreinfo/swivel-led/18-12-heavy-duty-swivel-led-utility-light-bar-w-12-leds-and-rocker-switch/1230/

These come in a variety of lengths and rotate 90 deg, I installed one in place of the fluorescent bulb above the Ice box and one for the Nav desk.  They come in handy because they only require two screws to mount, are lightweight and can be adjusted to shine directly down or back towards the bulkhead.  I mounted them on the teak piece which is underneath the trim mounted at 45 deg. 

[Jon W]

Noticed your mirror is on the wall to the right of the sink. Mine is on the bulkhead by the toilet.

Anyone know which is the original OEM location?

[Stu Jackson]

Noticed your mirror is on the wall to the right of the sink. Mine is on the bulkhead by the toilet.

Anyone know which is the original OEM location?

Doesn't really matter, does it?  I'm not even sure there was an OEM mirror. 

Mine is on the forward bulkhead. 

[Noah]

Mine is foward too, and when I got the boat there were cheapo bayonet round incandescent puck lights not fluorescent. On a 30 year old boat with many previous POs, the term "standard" is kinda moot. I changed all fixtures to LED, using a variety manufactures to fit the location: from Dr. LED, to Hella chart light to Luna Sea, to Alpenglow, which are my and Practical Sailor's favorite.

[Ekutney]

Mirror is one the forward bulkhead in the head, the mirror in the picture I posted is a small medicine cabinet mounted to the aft bulkhead.

I agree with Stu's comment... On a 30 yr old boat it's hard to know what was standard. 

As an example I have Maxwell winches, I was told there were original.  I also had three water tanks, one in the V berth, one starboard side under the settee and a great big water bladder under the aft berth.

[Jon W]

No, doesn't really matter. Just curious.

[KWKloeber]

Paul

Note that Nate is developing a red/white LED replacement for fluorescent tubes -- that will operate just like the red/white switchable LED fixtures and bulbs.  The last I heard it isn't in production.... maybe soon.

-ken

I want to replace my fluorescent tubes with the following:  12" F8T5 LED Tube for Fluorescent Fixtures (FL-T5-66)
These are from Marinebeam.  Has anyone done this change and what brightness did you choose?
The original came from West Marine and are working fine,  need more light.
Thanks, Paul

[Paulus]

I replaced the 2 fluorescent tubes with the 12" F8T5 LED tubes.  Had to remove or disconnect the ballast and rewire following their instruction.  Installed the light on the boat yesterday.  Very pleased with the extra light.
This company was easy to deal with and great customer service.

https://store.marinebeam.com/marine-led-fixtures/

[KWKloeber]

Paul, did it come w/ printed instructions you can post?
I need to do the same, though I think I'd be able to figure it out.  Is the new tube indexed (a pos and a neg end?)

ken

[Paulus]

It came with instructions for a 1 tube light but their web site has a link for the 2 tube light.  I can post it if you want.  Let me know.
Paul

[KWKloeber]

That would be great.  here or wiki  Thanks Paul.  It never hit me that we'll have to remove the ballast, etc. 
D'oh.  12v is 12v right?  LOL

[Paulus]

Here are the instructions

[Noah]

It has been mentioned here before... Some of the older incandescent light fixtures may not be suitable or work efficiently as they should/could using LED replacement bulb technolgy and it might be better to just replace with new LED fixture. May have issues with both light dispersment pattern/shape using existing lens as well as heat issues?