Join the C34 Association Today!
[C34 Home] [C34Tech Notes] [C34 Tech Wiki] [Join!]
Please login or register.
Advanced search  

News:

Pages: 1 [2]   Go Down

Author Topic: Transmission failure  (Read 305 times)

0 Members and 1 Guest are viewing this topic.

Noah

  • Administrator
  • Forum - Master Chief Petty Officer
  • *******
  • Karma: 19
  • Posts: 1663
    • View Profile
Re: Transmission failure
« Reply #15 on: June 30, 2020, 05:16:43 PM »

If you go for that transmission you might as well shorten your shaft at the same time. Minimal added cost and would also be an opportunity to inspect, polish and true. Ideally the prop should be 1in. behind the strut.
Logged
1990 hull #1014, San Diego, CA,  Fin Keel,
Standard Rig

KWKloeber

  • Forum - Master Chief Petty Officer of the Navy
  • ********
  • Karma: 32
  • Posts: 3520
  • "Positive Impact" 1984 C-30 #3573 trbsfk M-25
    • View Profile
Re: Transmission failure
« Reply #16 on: June 30, 2020, 05:22:48 PM »

Dh

What are the particulars - model # or MPS item # etc?
Logged
Twenty years from now you'll be more disappointed by the things you didn't do, than by the ones you did.
So throw off the bowlines.  Sail away from the safe harbor.  Catch the tradewinds in your sails.
Explore.  Dream.  Discover.   -Mark Twain

dhagen

  • Forum - Seaman
  • **
  • Karma: 0
  • Posts: 27
    • View Profile
Re: Transmission failure
« Reply #17 on: July 01, 2020, 07:48:40 AM »

It is a Baysan BMT-M30-2.00.  If I have the shaft shortened, I would have to have the boat hauled, which I don't want to do at this point.  Maybe when It is hauled for the winter.
Logged

Dave DeAre

  • Forum - Seaman
  • **
  • Karma: 0
  • Posts: 40
    • View Profile
Re: Transmission failure
« Reply #18 on: July 01, 2020, 12:05:26 PM »

I replaced the transmission on my 2002. Yes, the aft cabin must be empty, the "box" can be easily removed with 4 or 6 screws. Coupling disconnected and the shaft pushed back for clearance. Linkage disconnected and then the transmission bolts are accessed with a socket wrench and extension. Job is easy, unless any fasteners are corroded or frozen. It probably took me 4 hours total to do the job. Replace the damper at the same time.
Logged
Overdue
2002 34, roller main, tall rig
Burnham Harbor, Chicago

Ron Hill

  • Forum - Master Chief Petty Officer of the Navy
  • ********
  • Karma: 54
  • Posts: 6936
    • View Profile
Re: Transmission failure
« Reply #19 on: July 01, 2020, 02:51:28 PM »

dhagen : Rule of thumb - the prop distance from the strut should be one shaft diameter (1")

A thought
Logged
Ron, Apache #788

Bill Shreeves

  • Forum - Petty Officer 1st Class
  • *****
  • Karma: 2
  • Posts: 225
    • View Profile
Re: Transmission failure
« Reply #20 on: July 01, 2020, 07:46:06 PM »

dhag, I replaced my damper plate, tranny (actually a gearbox not a tranny I'm told), coupling, stuffing box, cutlass prop & shaft myself a few years ago.  The gearbox wasn't that hard.  Most everyone will tell you to always replace the damper plate when you remove the gearbox.  The cost will likely be all parts because it takes little time to actually replace and I'd highly recommend it while they're in there.  Also expect to pay labor for aligning the engine. If the gearbox is only longer and not lower there shouldn't be much if it was reasonably aligned before.  If it hasn't been aligned in a long time it might take more time because the mounts settle over years I'm told.
Logged
The only thing that always works on an old boat is the owner...

Bill Shreeves
s/v "Begnnings" 1987 Shoal Draft #333
M25XPB, Worton Creek, MD

dhagen

  • Forum - Seaman
  • **
  • Karma: 0
  • Posts: 27
    • View Profile
Re: Transmission failure
« Reply #21 on: July 02, 2020, 07:38:47 AM »

I removed the cabinetry yesterday. It was more than 4 screws, more like 8. The key trick is trying to figure out which eight!   And then getting at them through the opening in the top.
Logged
Pages: 1 [2]   Go Up