Join the C34 Association Today!
[C34 Home] [C34Tech Notes] [C34 Tech Wiki] [Join!]
Please login or register.
Advanced search  

News:

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - sailaway

Pages: [1] 2
1
Main Message Board / How many Catalina 34s were made
« on: January 15, 2018, 03:14:56 AM »
I wonder how many 34 where made I seen a number of 1400 the other day. Charlie

2
Main Message Board / fuel shutoff sticking
« on: June 18, 2017, 01:01:41 PM »
I have a 1986 with an M-25 engine. When I pull the fuel shutoff the engine stops . Then I push it back down the return lever on the engine stays in the off position I just move it back with my finger so it will start. I put a extra stop on the cable to push it back down no help. Is there some kind of spring return I am not seeing. Charlie

3
Main Message Board / catalina 50
« on: February 22, 2017, 12:09:53 PM »
Looking at my new mainsheet there is a pic of a catalina 50 hull # 18.  Never knew they made any 50s. Charlie

4
Main Message Board / fuel shutoff
« on: September 09, 2016, 04:44:25 PM »
Need to replace my fuel shutoff cable. Need to know the length of the cable. I have a 1986 34 with the shutoff located  in the engine gauge area. It's round knob I would like to replace it with the finger pull type. Charlie

5
Main Message Board / fuel consumption
« on: September 06, 2016, 02:17:04 PM »
I have an 1986 M25 engine that runs good but the fuel consumption has increased too 3/4 a gal per hour was 1/2 do I need new injections. Don't understand whats happening Charlie

6
Main Message Board / engine overheating
« on: August 13, 2016, 08:21:42 AM »
I have an 1986 m-25 engine it usually runs 165 -170 this wk we were a 1 wk trip in lake erie the water temp is 79 degree. my engine temp went to 180 on the long days. I also lost about 4 oz of antifreeze everyday. I am wonder if the heat exchanger is bad. I check all the normal things engine strainer baskets. water flows seems ok Charlie

7
Main Message Board / new roller furler
« on: May 03, 2016, 01:46:36 PM »
I am installing a new Schaefer my old one gave up. I have a 1986 34 with an old stay steam 2 furler. It was 30yrs old we sure got our money out of it. My book tells me the cable length std rig is 44'5" that is correct but overall its 45'5"the drum takes up 1' I measured everything be for I started the cable is one piece no turnbuckle. I just got the old one off. Has any one done this before I am looking for some tips. Charlie

8
Main Message Board / roller furling
« on: November 16, 2015, 05:51:55 PM »
Looking to replace my old roller furling with a new one. I am not sure what to buy was looking for some input from all of you. Was thinking about a continuous line who makes a good one. Charlie

9
Main Message Board / forestay length
« on: October 16, 2015, 02:00:57 PM »
I have a problem with my roller furling so I measured the length from open pin hole open pin hole was 46ft. My book says 44ft 5in.    I wonder what I am doing wrong. 1986 std rig Charlie

10
Main Message Board / Stuck jib pro furler
« on: September 27, 2015, 03:40:54 PM »
Just got back from the boat had a problem could not get my jib to come down. It came down about 10ft an stopped tried 3 times same spot. I think one of the sections of the roller furling track has separated. I have a 1986 pro furler . Has anyone ever repaired them can I buy parts. Or do I need a new furler Charlie

11
Main Message Board / prop shaft packing
« on: December 24, 2014, 04:45:10 AM »
Have been using gortex  but someone commented that there is a new packing that is dripless. Can't remember the name. Charlie

12
Main Message Board / engine antifreeze pump
« on: October 23, 2013, 03:26:20 PM »
I own a 1986 34 with  an m25 universal engine, I want to purchase a water pump for the antifreeze. A friend of mine had is fail. does anyone know the part number or a good supplier. Charlie

13
Main Message Board / beckson ports
« on: May 08, 2013, 05:27:36 PM »
My cabin portlits have become not clear do to age and cleaning agents. Is there any thing I came do to clear or resurface them. Charlie

14
Main Message Board / cutless bearing
« on: April 17, 2013, 05:55:20 PM »
Have 1986 34. The shaft has maybe 1/8 play. would like to replace in fall. I assume catalina direct would be the place to buy a new one. what is the best way to change a cutless bearing. Charlie

15
Main Message Board / roller furler failure
« on: June 26, 2011, 05:30:41 PM »
Had a problem with furling jib would not come out. I have a 1986 pro furl. Got back to  the dock furler would not turn.  Took the jib off every thing check out OK.  Put the jib back on every thing is OK now. I think maybe the halyard shackle got caught on the furling foil. Has any one had a problem with the furler. Charlie

Pages: [1] 2