I'm curious....
Has anyone installed the Zarcor Companionway Doors on their boat? I've looked, touched, felt and almost tasted them while talking to John at all the various boat shows they attend.
I'm interested as we now live aboard, every time we go in and out we have to take the crib boards in and out. Yeah, lazy -- I know.
No experience with the doors. They look great closed, but look like the will be in the way when open.
When I was living aboard (we still use it) I cut a piece of 3/8" plexiglas that fits in the slot instead of the 2 hatch boards. It allows more light into the cabin while keeping air conditioning or heat in. I have a sunbrella cover that snaps onto the teak strip on the companionway slide, draps over the insert for privacy or if you want to keep the light out. You still have to be remove it to get in and out, but only one piece and it's light enough to do with one hand.
The major issue I recall that folks have with doors is that the bottom of the companionway is lower than the sides of the cockpit seats, so the doors only open 90 degrees. I also recall seeing someone, perhaps in Mainsheet although not necessarily a C34, with a door design raised the bottom of the door section so that the doors could open and rest against the back of the cabintop so to be fully opened. Depending on your situation that may or may not be a necessary feature.
Lance,
We also have a one piece tinted Plexiglas or lexan hatch board and we really like it. As mentioned, it allows light in the cabin even when the weather's bad and I believe it's easier to take in and out than the two hatch boards. We also have the sunbrella cover with snaps on top but just weighted on the bottom so that you can use the sunbrella cover without the hatchboard if you want to keep in the heat at night but want to go in and out easily. Also, when the cover is not needed, you can just roll it up and leave it in place just behind the traveler.
If I can dig up some pictures, I'll post them.
Mike
I have thought about doors for a long time. How about a hatch board that is about 2" or 3" taller than the seats & doors above the hatch board. Yes, you still have a small board to remove, but only one & it would be light weight. The hatchboard would allow shorter doors that would swing open a full 180. The doors may need to be several inches above the seats because of the companion way gets wider from bottom to top. Cut a ship lap on doors & hatchboard to keep out rain. Thought about using 1/2" stock to keep down on weight & using take apart hinges to remove doors if needed.
I have just about everything John from Zacor has invented on my boat already, (Stern seats, Cockpit table, cup holders etc...) so I'm sure I'll bite the bullitt and buy his companionway doors soon. Perhaps during the next boat show!
We had a very nice set on our prior boat, a Watkins 27, they were wonderful and easily lifted out to store while underway. Here is a picture:
(http://images50.fotki.com/v1525/photos/3/31944/76563/Hatchdoors1-vi.jpg)
More info about those custom doors and how they worked are at my website here: http://public.fotki.com/sailorick/yare_my_sailboat/yare_hatch_doors/ (http://public.fotki.com/sailorick/yare_my_sailboat/yare_hatch_doors/)
Rick
Guys : During the first summer I had the boat (1989) I made two 1/4" thick smokey lexan hatches that replicate the teak hatch boards. Then I also made two teak framed screens that also replicate the wooden hatch board.
With those 3 sets I can use any combination : two screens, one screen one lexan or one board one screen/lexan.
When we are at an unfamiliar dock/marina, it's nice to put in the lower screen and the top board and lock the boat when you're temporally away - but still have some ventilation. The two lexans are nice to be "closed up", but still have light. The thin lexans are stored under the port side salon cushions. Over the past 20+ years the lexans have become scratched, but all the better for privacy so I don't worry about the scratches. When we leave the boat at anchor (no T-storm likely) it's both screens or a lower lexan and an upper screen.
The 3 sets give you alot of combinations. A thought
About the doors getting in the way, I see they make the doors with lift off hinges which makes it really easy to remove the doors when you don't need it. Quicker than removing slats.
I realize it's a little different, but I really like this design. I pulled the pictures off of yachtworld.com, so I have always wondered if the owner felt it was a good design after it was installed?
Cheers,
Rick
That's a pretty good looking companionway door.
But I think I still like the doors with lift off hinges better. When out on the water, you can get them completely out of the way. People often like to sit with their backs leaning against that bulkhead facing the rear and you can't do that with the doors open.
Actually it looks to me like those are lift-off hinges...
They are kind of pricy but Cruising Concepts has them for sale. Picture on the companionway door page shows the door interference problem. www.cruisingconcepts.com
Lance, you might be interested in this posting....maybe you missed it since it's under "screen".
You'll see a few pictures of my installation.
http://c34.org/bbs/index.php/topic,4523.0.html
I have the Tc10018 type door and really love it. I lift them off and stow them in the rear cabin during the sail. They do need re-oiling the teak but not a bad way to go.
Doors
Doors
Mike,
Great doors! Where did they come from.
I made these.
So, Mike,
Would a case of Boudan, get me a pair of those? I can pick them up too!
and of course there's always the screen door version.
Lance,
The cost of making the doors was reasonable. I also purchased a full sheet of tinted acrylic to replace all the windows and the new doors. Total was < $400 for wood & windows + a little extra for hardware. I can send you pics w/ measurements if you're interested in making them
I'd love to get them.
Thanks