Text only | Text with Images

Catalina 34

General Activities => Main Message Board => Topic started by: Craig Illman on November 10, 2008, 01:42:27 PM

Title: Emergency tiller cover plate O-ring Mark 1.5+
Post by: Craig Illman on November 10, 2008, 01:42:27 PM
I have a drip coming through the emergency tiller cover plate. I expect that after 18 years that the o-ring has lost its effectiveness. Has anyone replaced theirs? Suggested sources other than Catalina? I might drop a note to Catalina Direct.

Craig
Title: Re: Emergency tiller cover plate O-ring Mark 1.5+
Post by: Stu Jackson on November 10, 2008, 08:00:17 PM
Try Ace Hardware.

Really...
Title: Re: Emergency tiller cover plate O-ring Mark 1.5+
Post by: Rick Johnson on November 10, 2008, 08:17:32 PM
The other boat shop - http://www.mcmaster.com/
Title: Re: Emergency tiller cover plate O-ring Mark 1.5+
Post by: waterdog on November 10, 2008, 10:42:33 PM
Craig.   

These newer boats are really difficult to maintain.   I have a simpler, more reliable older version with no cover on the emergency tiller.  I'll drop it off for you and take this complicated one off your hands.   No problem.

Steve

Title: Re: Emergency tiller cover plate O-ring Mark 1.5+
Post by: Craig Illman on November 11, 2008, 07:22:32 PM
Steve - I'm sure with a little creative work with a sawzall, you could give Black Dragon a step-thru stern too! You might need to re-engineer the backstay.

Catalina Direct said "sorry".

Stu & Rick - guess I'll try shopping around town this weekend, cover plate in hand. Although, I'm tempted to run a thin bead of clear LifeSeal around the seam. I think it'd break rather easily if I tried to unscrew the deck plate.

Just a dumb thought ........

Craig
Title: Re: Emergency tiller cover plate O-ring Mark 1.5+
Post by: waterdog on November 12, 2008, 01:18:37 PM
I was hoping, through trickery, to work my way up to a 2008 model, but it appears that nobody will fall for it.  I think Stu must be sending PMs warning other owners.  I guess I'll just have to carry on upgrading.   You're sure Craig?  Mine comes with a new paper towel roll/rolling pin combo...
Title: Re: Emergency tiller cover plate O-ring Mark 1.5+
Post by: Braxton on November 12, 2008, 02:51:40 PM
Steve don't give up hope.   Far crazier things have happened.  You've probably already seen this but one guy managed to barter his way from a paper clip to a house:

http://english.peopledaily.com.cn/200604/18/eng20060418_259160.html
Title: Re: Emergency tiller cover plate O-ring Mark 1.5+
Post by: Stu Jackson on November 12, 2008, 03:24:58 PM
Steve, no, no PMs.  I got one of the oldest boats around and I'm keepin' her!  Finally got her just the way I want things! :clap  Good try, though... 8)
Title: Re: Emergency tiller cover plate O-ring Mark 1.5+
Post by: waterdog on November 12, 2008, 04:22:45 PM
I know what you mean Stu.   I'm about half way there.   If somebody offered to swap me for a boat ten years newer I don't think I would get something with 1000 hours on the engine, all new glazing, the new inverter, water heater, chartplotter, diesel furnace, windlass, vang and smoke stains in the battery box.  I'd have to start all over again...   
Title: Re: Emergency tiller cover plate O-ring Mark 1.5+
Post by: Ron Hill on November 12, 2008, 06:22:52 PM
Stu : I glad you got your C34 to where you want it. 
I'm still working on mine 21 years later and can still see a couple of years improvements that are needed yet!! 
Text only | Text with Images